Save Money On Gas: Driving
How you drive your car can determine how much money you will save on gas. Here are some tips on how to save money on gas when driving your car. If you have a standard transmission you should always drive in the highest gear possible. In many cars gas efficiency will go down by 10% if you have the air conditioner running while you are moving. If you have a lower temperature setting on your A/C, use it. Run the A/C until the interior gets cooled down and then turn it off and let the fan circulate the cool air. You should never run your AC with your windows open. Cars that were built after 1990 don t need to warm up before driving in the morning. For the first five minutes of driving, don’t exceed 35 mph. The engine actually warms up better if it is driving instead of idling in your driveway. Driving the speed limit will help you out as well… maybe as much as 10%. Accelerate slowly when you are leaving a stoplight. The fastest person through the intersection just gets to spend more money on gas. If you follow the tip of driving in high gear, you won’t be accelerating all that much anyway. Try buying 87-octane gasoline (Regular). Read your car manual. Some vehicle advertisements tell you to use premium gasoline, but the owner’s manual actually says that 87 is fine. Turn the engine off when you’re stuck at a light or waiting for a train to pass or when you don’t expect to move for a few minutes. When the engine is idling and not moving, you end up with 0 mpg. Revving the engine is a huge waste of time and gas as well. Unless there is a mechanical problem with your car, there is no need to do this before you turn your vehicle off. If there is a mechanical problem, consider fixing it before it turns into a more expensive problem later on. Following these tips can give you an advantage over gas prices at the pump.Olivia is a writer with over fifteen years writing video scripts and webcopy. She authors several websites and blogs. for more information on how to save money on gas <a href="http://milagecare.myffi.biz">click here!</a>
Source: www.ArticlePros.com

Little Things You Can Do To Save Money On Car Fuel
Nowadays, car fuel prices are on the rise and consumers are suffering. Gone are the days when you can carelessly drive your car without worrying about burning up too much gas. There are important procedures that you, as a car owner, can take in order to improve gas mileage. The following are practical tips to conserve gas: Close Windows - Windows that are open can create air drag that can decrease the fuel consumption by 10%. Avoid Bumpy Roads - Rough roads should not be taken as much as possible. Dirt, bumps, rough roads and gravels can cause 30% increase in fuel consumption. Keep Your Car Light - Take out unnecessary baggage. The trunk should be kept clean, any gadget, tools or loads that are not needed should be taken out. 100 pounds of extra baggage can affect fuel economy by two percent. Drive Efficiently - Just drive reasonably within the speed limit. Remember that speeds of more than 60 miles per hour increase fuel consumption. Do not do sudden starts, accelerations and stops. Acceleration should be done gradually. The gas pedal should not be stepped on more than one fourth of the way down. This will allow the engine to function most efficiently. Gas conservation could reach up to 5 percent if sudden stops, jerks and accelerations are avoided. Make use of gears for overdrive and cruise control as needed. Check Your Car Regularly - The car should always be maintained. The engine should be given a regular tune up, the tires should always have the right air pressure and efficiently aligned, the oil should be changed when needed and air filters replaced regularly. Clogged filters can affect gas consumption adversely by up to ten percent. Don?t Burn Gas Unnecessarily - Turn off the engine whenever there is an opportunity. Idle engine wastes fuel. There are instances where the engine could be turned off; stopping for gas, waiting for someone, changing tire pressure, caught in traffic and a lot more. Don?t Warm Up Too Long - Lengthy warming up of the engine should be avoided. 30 to 45 seconds should be enough time. Also check if the automatic check is removed after warming up the engine. This is usually stuck which could usually cause poor gas and air combination. By following these simple tips, you will be surprised at how much money you can save on your car fuel. And guess what? The money really adds up if you continue to follow these simple practices for conserving car fuel! Dr. Drew Henry owns a network of auto-related websites, including <a href="http://www.carsandtrucksecrets.info">Cars And Trucks Secrets</a>, <a href="http://www.carrimsecrets.info">Car Rim Secrets</a> and <a href="http://www.caraudiosecrets.info">Car Audio Secrets</a>. Visit his sites today!
Source: www.ArticlePros.com

Installing Aftermarket Head Units
Are you thinking about installing your own car stereo head unit? Be sure to read this article and figure out what you will need to do to get it done. Upgrading the sound system is usually one of the first modifications attempted when we talk about car customization. The best place to start is with a good head unit. If you plan to install it yourself, read on for some technical tips from our experience installers. You will need a few tools to do the job right, so start by collecting some screwdrivers (flat head and phillips head), a socket set, wire cutters, wire splitters, butt connectors or heat shrinking sleeves, electrical tape, zip ties, solder and a soldering iron, and some patience. The first thing I would do before installing I would suggest buying the stereo wiring harness for your vehicle application. This will make the installation easier for you if you are a beginner, and it allows for easier replacement of the stock radio (if you choose to sell the vehicle in the future) and swapping or upgrading to a different aftermarket head unit. Begin by disconnecting the negative battery cable from the battery. This will ensure that you don’t accidentally cross any wires and burn out a new piece of equipment. Next, remove the old head unit. If you need to see how this is done on your specific vehicle, you can look up your vehicles application on installdr.com. This is a great resource for seeing pictures of how to remove the head unit. Once it is loose, disconnect the wiring harness and the antenna from the head unit and remove it completely. There are two types of wiring harnesses you can get. There is the universal wiring harness that connects to your vehicles existing wiring harness, and has the unfinished wire ends that connect to the color coded wires of your new head unit. There is also a wiring harness that has a harness on both ends, and just clicks in place on both sides. These are the easiest to install, but can be harder ot find to match your vehicle to the head unit. Most wiring harnesses are the universal type, so we will focus on those. If you have obtained the wiring harness, you will notice the color coded wires in the back of the head unit. The wires on the head unit and wiring harness should match. The head unit wires and the wiring harness wires will be partially spliced for easy installation. There are several good ways to connect the wires. One way is to use butt connectors, which crimp the wires within a connector. These can be picked up almost anywhere that sells/installs head units, or at Walmart, etc. My favorite way requires a soldering iron and heat shrinking sleeves. Twist the wires together tightly. Apply just enough solder to weld the two wires together. Now fold them over parallel to one of the wires. Slide the sleeve over the connection and heat it with a heat gun or good hair dryer. I have had to rewire or repair systems where butt connectors were used, but this could be installer error, and not a problem with the connectors themselves. I have never had any of the soldered connections fail. Once all the connections are made, and the sleeves heated and shrunk in place, I like to take a zip tie and tie them all together. Clip the excess zip tie for a clean finished look. Connect the wiring harness of the head unit to the wiring harness connected to the vehicle. Plug in the antenna (you may find you need an antenna adapter in some applications). Now slide the head unit in place, but don’t attach it yet. Reconnect the negative battery cable and turn on the head unit (make sure the key is turned to the ACC position). It should be functioning properly at this point. If you plan on adding an amp, or have purchased one for this setup, turn the unit off and connect the RCA cables. Run them through the dash to the floorboard and to the amp (more on how to successfully do this in future articles). If you encounter problems, you can email <A HREF="mailto:support@majesticmodifications.com">support@majesticmodifications.com</A> for help. Brought to you by <A HREF="http://www.majesticmodifications.com" TARGET="_blank">http://www.majesticmodifications.com</A>. Majestic Modifications is your online source for auto parts and accessories, installations advice and technical support.
Source: www.ArticlePros.com